9.22 Created 16.03.23 Bug fixes: 1) When starting a logger from the Wizard and an error occurred, then SeaStar could "exit" incorrectly. Sometimes an application error was reported and consequently sometimes SeaStar froze. 2) Wrong low battery warning in SNMS to rechargeable loggers. After defining the battery fully charged a low battery warning could be issued. 3) For rechargeable loggers a fully charged option was not available in deployment settings forms. 4) For rechargeable loggers’ energy estimation was not shown correctly in RDT and MDT files after a user "Fully charged" definition. 5) The option "Set conductivity to zero if OOR" in Edit>Reconvert definitions> was dependent on other settings. This option would only work if the DV RID value was selected in the Edit>Reconvert>Data definition. Enhancements: 1) For rechargeable loggers a recharge counter and last recharge date was added to the logger RID. 2) More information for rechargeable loggers - Recharge information included in RIT, MIT, RDT and MDT files. - More detailed information in Recharge definition window. - Rechargeable definition window is preset with deployment fully charged settings. 9.17 Created 07.12.22 Bug fixes: 1) In DST "TD-loggers" using PS-P=primary the last meas. could sometimes not be retrieved from RAM 2) Reconvert progress-window could freeze. 3) Error in Submitting Tickets. A hardcoded IP-address is now used. 4) SeaStar could interpret incorrectly the number of bytes stored in the 2-Flash Starmon tilt and Starmon compass. 5) DST milli-F burst selection error. In now only available in TD-normal. Enhancements: 1) Support for rechargeable Starmon tilt and Starmon compass 2) Download help-files under Help. 3) Close button available in Connection-Wizard for direct USB connected Starmon loggers. 4) Starmon tilt V23 Extended burst options support 9.05 Created 19.04.22 Bug fixes: 1) Data reconvert def. Init-error. Using "Current new measurement sequence definition" was not initialized, between selecting new recorder or new type. 2) DAD -> DAT info-window could freeze. 3) A T-only DST milli-F 10HZ burst sampling was wrongfully supported in SeaStar, only TD 10HZ burst are valid. 4) For DST CTD V20 Low type (0.1-5mS/cm) and Regular type(3-68mS/cm) could in air show conductivity values. 5) In general pre-deployment calculations, Starmon compass would only use half available data memory. 6) Salinity-switch logic limit info was missing. This applies only to DST logic CTD. This info is now in the RIT, MIT, RDT and MDT files. 7) Start NMS in MultiMode logic features could change. Applied to DST logic and DST logic CTD. Enhancements: 1) A new interface theme has been applied to SeaStar. With refreshing changes to icons, colours and fonts. 2) New option: Disable copying of Reconvert files to sequence subfolders. This option can be found under: Settings>Options>Conversion 3) MID and MDT are now copied to sequence subfolders. 4) Minutes and seconds are now optional along with milli seconds in online measurements 5) When measuring online in SeaStar the DST CTD is now in a graphical interface. 6) Online measurements in SeaStar are now saved to disk continuously This applies to the following recorder. Starmon TD, Starmon Tilt, Starmon mini USB Starmon compass, DST CT, DST CTD For other recorders online measurements are in RAM and saved to disk on "Exit" 7) For DST logic CTD the "Salinity Switch only" logic limit is now default ON. Also, the depth logic is disabled. 8) 5 year battery warning for DST's 8.96 Created 24.11.21 Notice: End of SeaStar support for the following longtime discontinued loggers: DST Bird DST compass DST CompTilt DST GPS Starmon GT Support for DST centi-ACT now only in Mercury Bug fixes: Workaround procedures/messages in SeaStar to prevent excessive battery usage, in the following loggers. Starmon TD, Version 19 Starmon tilt, Version < 21 Starmon compass, Version < 11 Starmon mini USB, Version < 11 Enhancements: New improved user manuals for the following loggers: DST nano DST micro DST milli DST milli-F DST centi DST CTD DST Logic-CTD Dst tilt Dst magnetic Starmon mini Starmon mini-USB Starmon TD Starmon tilt Starmon compass 8.90 Created 27.9.21 Bug fixes: Fixed a erroneous CRC-error message when retrieving data and when the byte count was over 32000 This bug came with V8.87 and only affected DST tilt and DST magnetic Enhancements: Support for 600Bar pressure sensor 8.88 Created 10.8.21 Bug fixes: 1) Fixed a erroneous error message: File is empty or corrupt 8.87 Created 22.07.21 Bug fixes: 1) Starmon TD on-line range check error 2) Starmon TD V19 memory def. 3) For DST milli and DST milli-F. Wrong "No-measurement" symbol Sometimes a zero was used for a non secondary measurement. 4) Convert -> DAT information window occasional freeze 5) Small Reconvert information window removed This was an unnecessary information window 6) Template not always read correctly Count-index in the Template file list could become corrupt. 7) Save button in Graph, filename error Header reading error could occur resulting in a filename error. 8) New Header Date-Time separation indication Separation was not always performed in the data file according to header definition. 9) Settings>Options default settings "overtake" In certain circumstances default settings could be reset in Settings>Options Enhancements: 1) Improved Smart-Erase information messages 2) DST CTD V20 wide range conductivity (3-68mS/cm) support 3) Starmon TD V19, high USB speed support 4) DST magnetic V8 high magnetic resolution and improved heading calculations. 5) Zoom-total back => disable points In graph window on user "Full zoom out action" points are disabled. 6) For DST tilt, DST magnetic and Starmon tilt a Roll parameter is added in the DAT file. 7) CSV export button in graphs Exports the whole graph to a *.CSV file with a single row header. 8) Re/Convert information window now has Progress bar 9) Better RAM access (2GB->3GB/4GB) 10) Data to graph window now has Progress bar 11) Export to Excel button in graphs improvements 12) After first convert an intermediate Information-Window is displayed when files are copied. 13) Option for NMS, RDT and MDT files: Simplified battery&energy estimation presentation. This option can be accessed under Settings>Options>NMS-calc. 8.74 Created 18.12.20 Bug fixes: 1) Zoom error in on-line measurements. Sometimes the zoom would not react. 2) Sometimes the View on-line data operation would fail: (*.ONL) not found. 3) Under certain circumstances an error in view on-line data could occur : "Not a valid date and time" 4) On-line unit OOR correction could give misleading data. 5) OOR-decimal temp-press 15/16bit limit def. error. related to Starmon TD. 6) DST centi-HRT ACT time shift correction, with an option in reconvert data definition. 7) Sometimes a Reconvert option was available when changing recorder types, although no sequence was selected. 8) Starmon compass User cal menu udate 9) Missing ACC unit decimals def. for Starmon tilt. 10) Default Pressure/depth units got tangled. Enhancement: Introducing a new Starmon mini USB type with lots of features 8.55 Created 29.07.20 Bug fixes: Number decimals for acceleration unit values (in the ACC file) increased from two to four. 8.54 Created 13.07.20 Bug fixes: 1) Bubble comments not always cleared in GUI on OK and Cancel 2) On-line-measurements errors with Starmon tilt and Starmon compass 3) Numbers in the A90 Measurement column not correct 4) View DAX file via Measurement data was available for other loggers than Starmon compass 5) Update check message box now on timer 6) Starmon mini NMS Batt calculation HighRes type meas def. error. 7) DST CT was missing velocity unit def. 8) Reconvert DATA definition: Bigger fields for Pressure and Temperature linear correction 9) Starmon TD. To many measurements defined by SeaStar when retrieving data. 10)On-line measurement errors: Unit meas: Temp and Press with fixed 2 decimals. XYZ with non. Bin meas: X with 2 decimals. 11)Help files update error Files were placed in HelpFiles directory instead of Hlp directory 12)Setup-NMS file T-only errors. -T was not included in the name Number of measurements were listed as for a TD logger. This relates to DST Centi, DST Milli, DST Milli-F, DST Deci and DST Micro. 13)"Out of memory" error. This was a error that could appear when converting huge data files. This relates to Starmon tilt and Starmon compass 14)"Date is less than .." error message after 'On-line" button selection. This button was available in a Measurement sequence definition GUI, when the logger was on-line. This option has now been replaced by the "Default" option. 15)Repeated false RID message = "wrong number of measurements" 16)Error in logger time vs. PC-time to check future-time measurements in reconvert. User can define number of byte to retrieve so measurements can end in the future. 8.39 Created 16.04.20 Bug fixes: Out of range error in Online measurements for: Starmon tilt Starmon compass Enhancements: In Starmon compass DAT file added 4/8/16 points header parameter 8.38 Created 07.04.20 Bug fixes: 1) Histogram Compass and Tilt Compass would not show NESW bins and tilt would not show -90,-60,+-20,60,90 bins 2) DST nano RIT file showed 1 minute shift in start time. 3) DST nano RIT file showed to much battery usage 4) DST micro showed 1 meas to much in DAT after data retrieval 5) DST nano on-line measurements froze 6) An Excel-button created Excel-file had a copy to other workbooks/sheets error A message said: "This action won´t work on multiple selections". 7) OOR-max-bin def. not right for all logger-types 8) At connection time not always the right number of measurements taken reported. 9) RIT/MIT sometimes (depending on version) wrong DST Nano-T memory capacity def. reported 10) NMS file calculation reported wrongfully: Out of memory. Enhancements: 1) Added support for Starmon compass. 2) Flash memory blank test after Flash-Erase operation in SNMS. 8.17 Created 24.10.19 Bug fixes: The following only relates to Starmon mini 1) Starmon mini older type with baud=19200 would sometimes not communicate via Recorder>Connect, but the Wizard was working OK. 2) Under certain circumstances when data was retrieved an anomaly in the interval definition could trigger an error in the battery calculation estimating the battery energy to be 100%. 3) When setting the Starmon mini with multiple intervals then the NMS file was not displayed. 8.06 Created 17.09.19 Bug fixes: Related to Starmon tilt. 1) Time-tags on tilt burst values in A90-graph were shifted 2) Error in measurement parameters definition in multiple intervals The measurement parameter index from the single interval was used in the multiple parameter setup. There are three scenarios for this: a) After SeaStar is started the user uses the multiple interval option right away to setup the logger. Then all intervals measure TD and tilt, including the 20Hz, 50Hz and 100Hz burst options. This means there is no error if Normal, 5Hz burst or 10Hz burst is applied. b) After SeaStar is started the user uses the single interval option for testing Normal, 5Hz burst or 10Hz burst. Then using the multiple intervals to setup the logger. This results in the same error scenario as in a. c) After SeaStar is started the user uses the single interval option for testing 20Hz, 50Hz or 100Hz bursts. Then using the multiple intervals to setup the logger. This means all intervals measure only tilt, including the Normal, 5Hz burst and 10Hz burst options. Please note: By reconverting older measurements this version will show correct measurement parameters. 7.91 Created 21.2.2019 Enhancements: For PT Geyser: Pop up statistics shown in NMS file. Bug fixes: Fixed error causing Smart Erase function to terminate. For PT Geyser: Battery calculation correction 7.85 Created 4.12.2018 Enhancements: A new function, Smart Erase, is now active after a lengthy test period. The function minimizes the Flash memory erase time at startup. This is only relevent for : Starmon TD and Starmon tilt. Bug fixes: CRC check error fixed for DST micro-TD Ticket system fix. The ticket system was inactive due to changes in Star-Oddi IT-system changes. The ticket functions in SeaStar have now been adapted to the new Star-Oddi IT system 7.80 Created 9.7.2018 Bug fixes: Realtime clock Trim value corrections. 7.76 Created 24.5.2018 Bug fixes: DST micro-TD, SeaStar reported to many measurements taken. 7.70 Created 23.4.2018 Enhancements: PT Geyser CLS-Argos data conversion Bug fixes: Error message after Disconnect in Recorder Wizard: Sometimes a misleading popup message could appear after disconnecting: "EscapeComFunction failed". Retrieving ID halts in Recorder Wizard. Occasionally the recorder ID retrieval failed without a message. Floating-point or range-check error when reconverting with a user defined number of data. This effected only DST tilt. A90 graph: The *.A90 graph was not being displayed. Starmon tilt : New more accurate energy usage parameters implemented Connection error RID related: If for any reason the RID becomes severely scrambled connection could be jeopardized. False connection RID related: If for some reason RID transfer was not completed correctly then under certain circumstances the logger could be defined as on-line. 7.61 Created 9.3.2018 Enhancements: Added support for Starmon Tilt. 7.58 Created 29.1.2018 Bug fixes: Fixed error where in some instances .RDT file was not created. 7.57 Created 18.1.2018 Enhancements: Orbital parameters for PT Geyser Bug fix: Reconversion number was not always cleared between loggers. 7.55 Created 20.11.2017 Enhancements: Optimization for g added in depth calculation. Heat correction added for Starmon TD depth calculations. Bug fixes: Fixed illegal input in New measurement sequence menu causing logical errors. Fixed fail when writing to ACT file for DST tilt. 7.49 Created 11-05-17 Enhancements: Change to Change text "Activity" to "ACT" For logic type loggers a new option for disabling limit check was included 7.47 Created 04-04-17 Enhancements: Application version number is written into log file on start and exit Widened the boxes in connection wizard Starmon-TD user can enable invalid measurement check (ignore measurement if all bytes are 255) Installer help files are now in recommended Changed "Tilt Boundary" to "External Acceleration (EAC)" Bug fixes: Chart axis were not correctly set when using primary/secondary sequence If application doesn't have write access in user directory then default directory is used Incorrect data convertion for burst Disabled burst for DST milli-F versions under 15 Primary/secondary convert didn't correctly use the last measurement taken if it was in RAM 7.46 Created 17-03-17 Enhancements: Changed text "Number of meas." to "Number of measurements" PtGeyser v22 DST centi v15 Bug fixes: Removed view magnetic files option for non-magnetic recorders Removed view activity files option for non-activity recorders DST centi v14 is a normal memory type only 7.45 Created 15-03-17 Enhancements: Starmon TD SNMS now always performs a total erase Bug fixes: Incorrect burst data convertion Incorrect burst message count when connecting to recorder Removed burst option for DST centi-T When zooming with the mouse scroll the chart cursor did not always stay in frame Remove future values did not work correctly when reconverting Connection wizard didn't close after a successful SNMS when using multi mode 7.44 Created 15-02-17 Enhancements: Close connection wizard after a successfull SNMS Bug fixes: Error when running application from protected windows folders 7.43 Created 10-02-17 Bug fixes: Installer was missing USB drivers for Starmon TD Trim test is not supported by all recorders, now skips the test if not supported If trim test failed showed an incorrect message 7.42 Created 09-02-17 Enhancements: Change recorder type is now a warning instead of an error message Set pressure to zero if negative is now disabled by default Set conductivity to zero if value is out of range is now disabled by default and stored for next time Connection wizard now has a slight delay so that it is more able to find recorders out of battery Bug fixes: View .MAG could become disabled when changing to a magnetic recorder type 7.40 Created 14-12-16 Added long-term support (LTS) Added DST centi-ACT Added salinity switch for DST logic CTD 7.35 Created 14-09-16 Enhancements: Support for Starmon TD 7.33 Created 19-08-16 Bug fixes: Removed AM/PM text from "Start delay" in ".RIT" files Optimized "Export as Workbook", now uses less memory (memory was an issue with very large files) 7.32 Created 31-05-16 Bug fixes: Error in DST tilt burst calculations Error in tilt and magnetic reconversion user offset adjustment definition 7.31 Created 15-05-16 Enhancements: Remove logger window sets focus on OK button after timer Graph window now uses mouse wheel to zoom in and out by 15% Graph window now activates graph or table when the mouse is placed over it Bug fixes: Graph window zoom button set to disabled at start Graph window removed a stray label 7.30 Created 12-05-16 Enhancements: Start new measurement sequence now displays an image when finished, the dialog cannot be closed for 5 seconds while the user disconnects the recorder. Added colour coding for chart tables Connection Wizard: Optimized detection speed. Windows: for each recorder text windows are now grouped together in a tabular window Windows: for each recorder graphical windows are now grouped together in a tabular window. Mouse-right-click enables move to main window. Bug fixes: Burst: Fixed cases where burst in multiple recording intervals was incorrect (DST centi, DST tilt) Connection Wizard: Fixed an error detecting nano recorders. Recorder setup: When no recorder was selected for Dst micro the PS was not enabled. Recorder setup: When no recorder was selected for Dst centi or Dst CTD types, subtype definition could prevail when selecting other types. Changing range values in Dst tilt and Dst magnetic was removed. This could result in erroneous results when converting. Sequence definition: Error messages are now restricted to the number of intervals used. 7.24 Created 04-02-16 Connection Wizard: Type and serial can't be displayed if the logger was in measurement mode, displaying this information is removed 7.23 Created 01-02-16 Connection Wizard: Fixed an error where the baud rate would be incorrectly set causing Timeout on Command Echo Connection Wizard: Now displays Unavailable if that COM port is not accessible, for example used by another program Connection Wizard: Now when the icon turns green also displays the recorder type and serial 7.22 Created 15-01-16 Submit ticket now allows PNG files to be added as screenshots Tilt origo function correction for Dst Tilt 7.21 Created 20-11-15 New update system 7.20 Created 16-11-15 Fixed an error causing that blocked running multiple instances of the program DST magnetic, fixed an error that caused directions to be incorrectly calculated 7.19 Created 5-11-15 Added new export button to graph that creates an excel file in xslx format Enable conductivity logic limit now default on 7.18 Created 15-10-15 Minor enhancements to the connection wizard (F11) 7.13 Created 04-08-15 Fixed an error with DST CTD online measurements where salinity calibration constants weren't used 7.12 Created 03-07-15 Fixed a bug in Starmon-mini where it would not use extended memory in memory calculations 7.08 Created 20-05-15 Support for new version of Dst milli-F (v15) 7.03 Created 03-02-15 Fixed an error when converting data with Starmon mini freeze 7.02 Created 03-02-15 Minor changes to Starmon ES Support for Starmon LC 7.00 Created 27-01-15 New installation and product verification 6.17 Created 16-12-14 Online measurement errors: Incorrect use of decimal separators in online unit conversion Binary version of the file was not correctly generated. 6.16 Created 10-12-14 Fixed an error when connecting to a recorder with the connection wizard and using an invalid cable type. 6.15 Created 17-10-14 Bug fixes: Fixed an error when converting data for multiple logger types 6.14 Created 14-10-14 Enhancements: Support for DST nano version 10 Bug fixes: Fixed a possible error when disabling gridlines Fixed an error in histogram where number of points and other values were not correctly calculated for primary/secondary Fixed an error in histogram where the default bin values were incorrect Failed tickets are now saved and can be sent as email attachements to support@star-oddi.com 6.13 Created 17-09-14 Bug fixes: Fixed a possible error when retrieving data 6.12 Created 12-09-14 Bug fixes: Fixed an error when retrieving data and pressing cancel Fixed the response time of using cancel when connecting to a recorder 6.11 Created 12-09-14 Bug fixes: Removed series click and statistics is now changed using horizontal gridlines Fixed an error where primary / secondary data was not displayed correctly Table is now fully visible on load COM port is now displayed correctly in the bottom panel 6.10 Created 27-08-14 Enhancements: New connection wizard, shortcut key F11 New charts, faster loading Admin privileges are no longer required BDE is no longer used New recorder Starmon TD Online measurement displays data visually in real time for: Starmon TD, Starmon GT, Starmon ES, DST centi, DST milli, DST nano and DST micro 6.07 Created 25-03-14 Bug fixes: Important work-around for an unexpected battery drain during the start delay period: This error only effects DST Micro-T V17 loggers, and only if they have been started in the year 2014. By using SeaStar V3.07 this extra battery drainage is avoided. The Compass boundary limit test was disabled: This is now always ON. By setting the boundary limit to 0° the limit test is effectively disabled. Starmon min-freez: This is product that is under testing at the moment. Sometimes in the Capture line Starmon mini received a -freez notation Enhancements: Compass heading correction: There is now an option to use last heading value if the ACC vector exceeds 1.2g or is less than 0.8g. This option is available in . The default setting in OFF. 6.06 Created 24-03-14 Enhancements/Miner bug fixes: Starmon mini port def.: Starmon mini now starts with the port selected and power ON. Default logger: When SeaStar is installed the default logger now is DST CTD. Previously it was DST CompTilt, but that logger has now been replaced by DST magnetic. DST CompTilt is still supported by SeaStar. RID comparison used in connecting to recorder: If the CRC test fails twice but RID comparison between the two RID´s retrieved, is a 100% match, then the RID transfer and the connection is deemed OK. The reason for this is that when a start procedure is halted midways, a new RID has partly been uploaded to the logger, and the CRC number will therefore inevitably be corrupt. 6.05 Created 24-03-14 Enhancements: Header correction: There is now an option to use last header value if Pitch or Roll exceeds 45° This option is available in . The default setting in OFF. Pressure UV truncation: Pressure unit values are now shown as zero if values are less than zero. The reason for this was mainly that decimal values outside calibration range, if not corrected by "Last" or "Max/Min" values can appear strange. This is user changeable in reconversion via . The default setting in ON. Bug fixes: MID file creation: MID file was not created if no data in recorder but data retrieved according to user def. Umin and Vmin range def.: User reconversion Umin and Vmin range definition option was expanded from 4095 to 65535 Depth calculation: The pressure calibrated value is in BAR. Converting to PSI or depth values in meters or fathoms is optional. Seawater density is default. The error lay in the conversion to meters mainly when selecting fresh water. CIT update: Seawater/Fresh water selection was not registered in the CIT file 6.04 Created 06-03-14 Bug fix: In Starmon-GT V1.0 only: Wrong address pointer for save data in SNMS. 6.03 Created 04-03-14 Support for Starmon mini freez This is a subtype of Starmon mini with a Pt100 sensor and range from 25°C Minor changes Naming convention for DST CTD and DST CT Type selction: DST CTD & DST CT Type folder: DST CTD Bug fixes: Battery calculation correction for Dst milli and Dst Centi: If multible intervals where used with PS, sleep energy was estimated incorrectly. 6.01 Created 29-01-14 Bug fix: DAC error: If a serious error (like floating point error) occurs in conversion the DAC file is not closed. This error was introduced in V6.00 6.00 Created 29-01-14 Support for Starmon TD V1 Minor changes /bug fixes: View Online measurements Starmon mini HighRes improved energy calc. ROC calculation default off EP-ID error ignored if HW-ID OK 5.97 Created 22-11-13 Bug fix: Graphical prensentation of DST compass data. Only in V5,96. 5.96 Created 20-11-13 Support for Starmon GT V2 (GeoThermal) Support for Starmon ES V1 (External Sensors) 5.89 Created 01-07-13 Support for new version (V5) of Dst tilt. The new Dst tilt has: More memory Hardware tilt filter option Tilt measurement burst option, 5/sec Bug fix: Affects Dst Bird only: Light conversion fails. Unit values (in Lux) are shown as 0 in the DAT file. The DAB values are correct. Bug was introduced in version 5.80 OOR-options for light (Dst bird) have now been activated 5.85 Created 03-03-13 Bug fix: Compass Boundary Round Off was not available: Is now reinstated. This effects reconversion of Dst Compass, Dst CompTilt and Dst magnetic data. 5.84 Created 27-05-13 New Option: PNG A new chart image format option, PNG is now awailable. Bug fix: Changing bottom axis text. Problem in loading a chart template has been resolved. 5.83 Created 24-05-13 Bug fix: Fixed flash memory erase failure in Dst milli-F, introduced in V5.78 Reduced connection time yhat had increased in V2.80 5.81 Created 21-05-13 Bug fix: A fatal starup error in version 5.80: The libusb-1.0.dll file is missing. In this version the routines in the libusb-1.0.dll are included in the SeaStar.exe file. 5.79 Created 17-04-13 Bug fix: A range check error is reported when starting up a new measurement sequence. Recorder types affected are: Dst CTD Dst Logic CTD Dst magnetic (V5) 5.78 Created 11-04-13 New Dst Centi V14 Burst support Intervals can now be defined in Burst mode, sampling 10 times per second. Enhanced Erase features for Dst milli-F When erasing the Flash memory prior to starting a new measurement sequence, commmunication errors could stop the erase process. Now if a wrong reply is received, then repeated attempts are made (5 times for each page/sector) Bug fix: For logic recorders (Dst logic, Dst P&R logic and Dst CTD logic) Number of measurements taken is reported correctly. In defining a new multible interval sequence, there was a error in checking a sertain combination of primary, secondary and number of measurements. 5.75 Created 28-01-13 New conductivity conversion enhancement: Conductivity and Salinity are now shown as zero if conductivity decimal values are less than calibration lower limit. The reason for this was that values outside calibration range, if not corrected by "Last" or "Max/Min" values can appear as "valid" low salinity values. This is user changeable in reconversion via . The default setting in "ON". Moved reconvert option: Options for Temperature Correction when "Temperature is Outside Calibration Range" (TOCR) that was previously in was moved to . These options now apply to Pressure, Conductivity, Light and Magnetic measurements. Enhanced temperature correction option: An option to disable circuitry temperature correction is now available for pressure, conductivity, light and magnetic measurements. Thus if temperature measurements are bad, missing or conversion coefficients are scrambled this option is available. Tilt 90° sum correction. Tilt measurements on each axis X,Y and Z are referenced to the horizontal plane and have a range of +-90. The sum of the absolute values of these three axes is theoretically 90. As the tilt values are based on acceleration measurements and the accuracy is limited, this is not always the case. Thus a 90 sum correction option is now available, based on relative value size optimization. Bug fix: A conversion error manifests itself as measurements are not converted or scrambled in conversion after approximately 7000 converted measurements. Bug appeared in V5.70, effecting "only" Dst CTD recorders, V8-V10. Raw data is not affected, thus in V5.75 reconversion gives correct results. Bug fix: Settings Conductivity OOR definition occasionally resulted in an "Access Violation" error. 5.70 Added new recorder type: Starmon TD 5.68 Added online feature for DST CTD 5.67 Added an error notification when attempting to start a bird tag with 45+ day delay 5.65 Tilt conversion has been reverted from 180° system. Adjust axis button function was corrected. 5.64 Minor Bug fixes: When installing from a CD, the working directory defined by Icons on Desktop and Start Menu was not sat correctly. Therefore ´s default file structure was created in the Icon directory. This has now be corrected. This bug appeared in V5.51 5.63 Minor Bug fix: If for some odd reason, the battery-life left registers in the recorder are zero, then the NMS battery calculation did not function correctly. This bug appeared in V5.62. 5.62 Bug fix: For Dst micro V11 a change was made in the real time clock (RTC) configuration. This means changes in the recorder registers, in the information data section (RID). SeaStar has not handled these changes correctly. This has been mended. New Wizard: A new menu item "Change battery Life" in the Wizard menu, is now available. This wizard was introduced to enable changes to a corrupt "Battery eneregy" register in the recorder. General User Interface (GUI) Changes: The "Reconvert definition" in the Settings menu was changed to "View Data". The two viewing related items in the "Retrieve Data" definition where moved to the "View Data" window. 5.61 Bug fix: Dst milli-F: In SNMS, before clearing RAM an extra delay was needed. Single Spike calculations: Regional settings applied. Dst CompTilt: Changin the magnetic vector referance is only an option in Dst magnetic Salinity offset: Max value is now 99999 (uS/cm) 5.60 Screenshots Submit ticket Temperature response time shift Tilt conversion Single spike correction Boundary Round Off Acceleration limit The *.A90 file Compass conversion Boundary Round Off Single spike Magnetic values conversion Magnetic field reference Magnetic temperature correction. The *.BMD file Minor changes Clock drift calculations. Update now tries 3 times to connect before resulting in a failure. Fixed an error where it was not possible to connect with old Starmon mini. TNR graph did not display all data columns, reconvert is needed to fix old data. 5.52 Bug fix: DAB file was not computed correctly, as pressure values where sat to zero (in 5.51) 5.51 Fixed a erroneous error detection and message when using Multiple Intervals in defining a new measurement sequence. 5.50 Added acceleration calculations for DST comp-tilt, DST geomag, DST logic P&R, DST magnetic, DST P&R and DST-tilt. The calculations can be viewed with "View-Data Trend and Table-Acceleration". For logger types that support temperature only thers is now a "Temperature only logger" checkbox in the "NMS Time and Energy calc." settings. The result of data retrieval is now logged, bytes received X of Y. OOR forms were redesigned. Fixed a bug where reconvert would be disabled after a logger measurement was selected. Fixed a bug where "Save Window Data" would have an incorrect destination folder after reconversion. 5.35 Major Changes Minor Changes Battery life estimation for the DST nano recorder has been improved. 5.33 Major Changes Minor Changes Battery life estimation for the DST micro recorder has been improved. SeaStar detects the memory size of the DST nano recorder. 5.32 Major Changes Minor Changes Fixed an error when retrieving data from T-only or CT recorders, this error cancelled automatic loading of the graph. 5.31 Major Changes Minor Changes ChangeLog is displayed if a new application version is available while updating. Application file size is now correctly displayed when updating. Spelling errors. Active series now allows the user to right click and select: all, none, invert. Low battery warning when starting a new measurement sequence if the battery level is below 20%. Wizards: if multi mode is active then the start new measurement settings is skipped and if completed successfully offers to repeat the wizard. Wizards: Added a notification to remind users to put the recorder in the communication box. Log files (Application log and SNMS) have been moved to a submenu "Log Files" under View. If multi mode is active and the new measurement sequence starting time is less than 2 minutes away then the multi mode is deactivated. Import now allows multiple files to be selected. Improved check for corrupted registers.